Laminar Mass Flow Controllers
Multi-gas control, 200:1 turndown, with pressure and temperature readout.
Diese Seite gibt es auch auf Deutsch.
Cette page existe aussi en français.
Flow control devices set and hold a flow rate, not just measure it: rotameters with needle valves for manual control, and thermal, laminar and liquid mass flow controllers that drive a valve to a setpoint. Manual glass-tube meters through digital multi-gas controllers, from millilitres to thousands of litres per minute.
Choose your technology
Multi-gas control, 200:1 turndown, with pressure and temperature readout.
For liquids — closed-loop volumetric control, 0.5 mL/min to 10 L/min.
Set flow by hand on a glass tube — no power or electronics.
Automatic gas mass flow control — heat-transfer sensor plus built-in valve.
Multi-gas controller reaching setpoint for 98+ gases, 0.5 smL/min to 5000 sL/min, full fieldbus I/O.
±0.8% RD · to 5000 sL/min
ANALYT-MTC
High-pressure gas controller to 22.1 bar a for 98 gases, 10 smL/min to 12 000 sL/min, fieldbus I/O.
22.1 bar a · to 12 000 sL/min
ANALYT-MTC
Corrosion-resistant gas controller, FFKM seals, 128 gases, 0.5 smL/min to 12 000 sL/min.
FFKM · to 12 000 sL/min
ANALYT-MTC
Low-pressure-drop gas controller for 98 gases, Δp from 4.8 mbar, 0.5 smL/min to 1000 sL/min.
Δp from 4.8 mbar · to 1000 sL/min
ANALYT-MTC
Digital gas controller with 200:1 turndown, batch totalizers and under-150 ms response.
±(0.5% RD + 0.2% FS) · 200:1
Aalborg
Laminar liquid controller holding a volumetric setpoint, 0.5 mL/min to 10 L/min, with full I/O.
±2% FS · to 10 L/min
ANALYT-MTC
Low-flow precision rotameter with direct-reading or mm scales and optional control valve.
±2% FS · 65/150 mm
ANALYT-MTC
PTFE and glass wetted parts for corrosive gases and liquids; single tube with optional needle valve.
±2% FS · 65 °C · 6.7 bar
ANALYT-MTC
Multiple-tube PTFE and glass meter for corrosive streams in individual channels or manifolded mixing.
±2% FS · 65 °C · 6.7 bar
ANALYT-MTC
Single-tube meter built for fast flow-tube changes and cleaning, with the same tubes as the P meter.
±2% FS · 13.8 bar · 120 °C
ANALYT-MTC
Blends two or three gases in variable concentrations at the point of use; 150 mm tubes, mm scale.
±2% FS · 150 mm
ANALYT-MTC
Rugged brass or 316 stainless meter for medium air and water flows, with dual rotatable scales.
±5% FS · to 900 L/min air
ANALYT-MTC
Medium-range brass or stainless meter with direct-reading scales for argon, CO₂, helium, N₂ and O₂.
±5% FS · 5 gases
ANALYT-MTC
PTFE-wetted medium-range meter for corrosive air or water, 100–625 L/min air, dual rotatable scales.
±5% FS · to 625 L/min air
ANALYT-MTC
All-PTFE, PFA and PCTFE meter for corrosive or ultra-pure liquids, 75 mL/min to 45 L/min.
±5% FS · to 45 L/min
ANALYT-MTC
In-line all-PTFE meter for high-purity or corrosive liquids from 125 mL/min to 45 L/min.
±5% FS · to 45 L/min
ANALYT-MTC
Bench kit with interchangeable 150 mm flow tubes and floats in aluminium, stainless or PTFE cases.
ANALYT-MTC
Thermal gas controller with integrated solenoid valve and tiltable LCD; aluminium or stainless.
±1% FS · to 1000 sL/min
ANALYT-MTC
Digital thermal gas controller with RS-232/485, totalizer and flow and pressure alarms.
±1% FS · to 100 sL/min
AalborgManual control means a rotameter with needle valve: the same glass tube reads the flow and sets it by hand, with no power or electronics, for gases and liquids at ±2% FS standard. Automatic control means a mass flow controller, which drives a valve to a setpoint and takes analog, serial or fieldbus control. Choose manual when a hand-set value is enough; choose a controller when the setpoint has to be held by the instrument.
For gases, there are two families. Thermal mass flow controllers use a heat-transfer sensor with a built-in valve, from 10 smL/min to 1000 sL/min N2. Laminar mass flow controllers work on differential pressure, reach setpoints for 98+ gases and report mass flow, volumetric flow, pressure and temperature, from 0.5 smL/min to 5000 sL/min.
For liquids, liquid flow controllers are laminar controllers that hold a volumetric setpoint from 0.5 mL/min to 10 L/min, with stainless steel wetted parts.
Compare the fluid first, then the range, then how the setpoint is set. A rotameter with needle valve covers gases and liquids with hand adjustment; the controllers above add automatic setpoint control, with gas or liquid as the deciding factor. Open the category that matches your fluid to compare accuracy, range and signals.
Our application engineers aim to reply within 3 business hours.