Sioutas Personal Cascade Impactor
Separates and collects airborne particles in five size ranges. Highly efficient at collecting particles without the use of impaction grease or substrate coatings.
Ultrafine Fine >2.5µm
Downloads
The Sioutas Personal Cascade Impactor separates and collects airborne particles in five size ranges. When used with PTFE filters the Sioutas Impactor is highly efficient at collecting particles without the use of impaction grease or substrate coatings, and at retaining unstable compounds for size-fractionated chemical analysis. It is the only personal impactor that efficiently samples coarse, fine and ultrafine particles simultaneously. Particles above each cut-point are collected on 25 mm filter in the appropriate stage with particles below 0.25 µm collecting on the 37 mm after-filter (optional). Use the Sioutas Impactor with the Leland Legacy sample pump at 9 L/min to ensure precise particle separation at the specified cut-points.
- Precise particle separation
- Particle size cut-points: 2.5 µm, 1.0 µm, 0.5 µm and 0.25 µm
- Maintains high collection efficiency even at high particle concentrations
- Optimised at a 9 L/min flow rate with low pressure drop for 24 hour sampling
- Improves analytical sensitivity
- Minimises non-detectable samples
- Preserves unstable compounds
- Chemically inert collection substrate
- No impaction grease to contaminate sample
- Minimal particle bounce and internal wall losses
- Suitable for indoor and outdoor sampling *
- Size-fractionated samples can be analysed gravimetrically, chemically, and microscopically
Applications
- Occupational hygiene studies
- Indoor Air Quality (IAQ) studies
- Air pollution studies
- Inhalation toxicology and epidemiological studies
- Aerosol research
- Pharmaceutical studies
- Outdoor ambient sampling *
* Requires special provisions, please see the Sioutas Cascade Impactor Instructions.
| Flow Rate | 9 L/min |
| 50% Cut-point | Stage A: 2.5 µm Stage B: 1.0 µm Stage C: 0.50 µm Stage D: 0.25 µm |
| Material | Anodised aluminium O-rings: BUNA-N Filter retainers: Acrylic |
| Maximum Operating Temperature | PTFE Filters with PMP support ring is 240°C |
| Recommended After-filter | 37 mm 2.0 µm PTFE with PMP support ring (Part no. 225-1709) |
| Recommended Collection filter for Stages | 25 mm 0.5 µm PTFE with laminated PTFE support (Part no. 225-3708) |
| Tubing | 3/8 inch (9.53mm) ID |
| Outlet Diameters | Inlet: 3/8 in OD and 1/4 in ID Outlet: 3/8 in OD and 1/4 in ID |
| Dimensions | 8.6 x 5.5 cm |
| Weight | 159g |
Filters for the Sioutas Impactor
The Sioutas Impactor uses four 25 mm filters (required) and one 37 mm filter (optional). The 25 mm PTFE filters act as a collection substrate and the optional 37 mm PTFE filter is the final collection filter (After-filter). We recommend PTFE filters to minimise particle bounce and to preserve unstable compounds. Coated collection substrate may be used if desired. However, a coating is not necessary and can interfere with chemical analysis.
Sioutas Personal Cascade Impactor
| Description | Pack Size | Part Number |
|---|---|---|
| Sioutas Personal Cascade Impactor | Each | 100-3002 |
Accessories
| Description | Pack Size | Part Number | |
|---|---|---|---|
| Replacement Collector Plates, set of 4 | Each | P55016 | |
| Retainer Rings only | 4 | P20151 | |
| Replacement O-ring, Retainer, and Spacer Set for Sioutas Impactor includes 4 filter retainer rings, 9 O-rings, and 1 PTFE spacer ring | Each | P51917 | |
| After-filter, 37 mm PTFE ‡ † , 2.0 µm, optional | 50 | 225-1709 |  |
| Collection Substrate (filter for 4 stages), 25 mm, PTFE † , 25 mm, 0.5 µm pore, required | 250 | 225-3708 | |
‡ Back pressure on PTFE filters can vary within the same lot.
† The maximum operating temperature for PTFE filters with PMP support ring is 240°C.
